Logo
Get Estimate

Thermal Imaging and Infrared Inspection Colorado Springs CO

Find hidden dampness before it spreads through your home


Thermal Imaging and Infrared Inspection Colorado Springs CO helps homeowners, buyers, and property managers investigate unexplained dampness without opening walls first. We scan temperature patterns, then verify suspicious areas with moisture meters and visual checks. Our infrared moisture inspection Colorado Springs service is useful after a roof or plumbing leak, when a musty odor persists, or before repair work hides the evidence.

A technician inspects an outdoor HVAC unit for maintenance.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Colorado Springs

What Thermal Imaging Includes

A standard visit covers a history review, thermal scanning of agreed accessible areas, follow-up moisture checks at selected points, and a clear explanation of observations. We note limitations and distinguish verified dampness from a temperature anomaly. Mold sampling, destructive openings, repairs, and laboratory analysis are separate services when needed; we recommend them only when they answer a specific concern.

Concern And History Review

We discuss leak timing, prior repairs, odors, stains, and rooms affected before scanning. Your information helps us choose useful comparison surfaces and avoid spending the visit on unrelated areas. Bring photos or repair details if you have them.

Thermal Surface Scan

We scan agreed accessible walls, ceilings, and floors with a thermal imaging camera, noting patterns that differ from surrounding materials. We account for vents, direct sunlight, and heat-producing equipment because those conditions can alter the image without indicating moisture.

Selected Moisture Checks

We use a moisture meter or pinless moisture meter to check selected materials where access allows. Readings are compared with nearby areas and interpreted in context; material type and surface condition affect what a meter can tell us.

Findings And Next Steps

We explain the areas checked, the patterns observed, and any readings that support further investigation. You leave knowing whether the evidence points toward drying, a leak check, monitoring, or a separate mold assessment rather than relying on an unexplained camera image.

Thermal Imaging and Infrared Inspection Colorado Springs CO


Thermal Imaging and Infrared Inspection Colorado Springs CO is a non-invasive building assessment that uses temperature differences to identify areas needing moisture investigation. A thermal imaging camera records surface temperatures; it does not see through walls or prove that water or mold is present. We compare suspicious patterns with nearby surfaces, then check accessible materials using a moisture meter or pinless moisture meter. This two-part approach helps locate likely water intrusion while limiting unnecessary cuts into drywall, ceilings, floors, and trim.

Colorado Springs properties face sharp temperature swings, winter freeze-thaw cycles, roof runoff, and indoor condensation when warm air meets cold surfaces. Those conditions can leave hidden mold behind drywall or damp insulation after a leak appears repaired. Our Colorado Springs thermal imaging inspection pairs thermal patterns with physical moisture readings and a room-by-room history. If you need an infrared inspection for hidden moisture in a Colorado Springs home, we trace the clues, document findings, and explain what should be checked next.

What To Expect During Inspection

Thermal Imaging and Infrared Inspection Colorado Springs CO follows a measured sequence: history, scanning, verification, and clear findings. Most residential visits take about 1.5 to 3 hours, depending on access and the number of affected rooms. You can stay present, point out odor or leak history, and see the areas we check.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools And Inspection Methods

Tools & Equipment

FLIR Thermal Imaging Camera

Records surface-temperature patterns across accessible building areas. We use the image to locate anomalies for follow-up, not to claim that the camera sees through walls or identifies mold.

Tramex Moisture Meter

Checks selected building materials for moisture-related readings. Comparing an area of concern with a nearby reference helps us interpret whether a thermal pattern deserves more investigation.

Protimeter Pinless Moisture Meter

Provides non-invasive comparative readings on suitable surfaces, helping reduce unnecessary marks during initial checks. Material type, thickness, and surface conditions remain important to interpretation.

Extech Hygrometer

Measures indoor temperature and relative humidity, adding context when we assess condensation or surface dampness. Room conditions help explain why a wall or window area may show a temperature difference.

Borescope

A borescope can inspect a limited concealed space through an existing opening when access is appropriate. We discuss its use when thermal and moisture findings leave a specific cavity question unanswered.

Methods & Standards

Comparative Thermal Survey

We compare surfaces with similar materials and exposure, then note temperature patterns that stand apart. Direct sunlight, HVAC airflow, appliances, and recent weather can affect readings, so we document relevant conditions and avoid interpreting an isolated image as proof of a leak.

Moisture Verification

A thermal anomaly guides selected checks with an appropriate moisture meter. We compare readings against nearby material and consider the substrate before drawing conclusions. This step helps identify which locations have evidence of dampness and which simply need observation or another type of assessment.

Building-History Correlation

We match scan observations to reported leaks, stains, repairs, odors, and room use. A pattern near a known plumbing route carries different context from a cold exterior corner. This approach supports a practical investigation plan and helps keep recommendations tied to the actual property.

ASTM D7338-Informed Assessment

We use the principles of ASTM D7338 Standard Guide for Assessment of Fungal Growth in Buildings to frame building observations and moisture conditions. The guide supports systematic assessment; it does not turn thermal imaging into mold identification or replace suitable sampling when identification is needed.

When To Schedule An Inspection

01

A frozen plumbing line in a Colorado Springs home leaked into a wall during a winter cold snap.

What we do: We scan around the leak path, including nearby flooring and ceiling surfaces, then check selected materials with a moisture meter. The inspection helps you locate areas that need drying and spot possible spread beyond the visible opening. We also explain where access is limited and what additional checks could clarify.

→ You get a targeted set of areas for drying or repair instead of relying only on the visible stain or the plumber's access point.

02

A roof leak after a storm left a ceiling mark, but the surface feels dry and the odor remains.

What we do: We review the roof repair history, scan the ceiling and adjoining wall, and compare suspicious areas with unaffected surfaces. Direct readings help determine whether materials still show elevated moisture. We document the pattern and tell you if further roof, attic, or mold investigation is warranted.

→ You can focus the next inspection on the locations supported by evidence and avoid assuming that a dry-looking ceiling is fully resolved.

03

A buyer notices old water marks and wants more information before a Colorado Springs property purchase.

What we do: We inspect the reported areas, scan accessible surfaces, and take selected moisture readings. Our notes distinguish current evidence from historical staining and identify any limitations, such as concealed cavities that cannot be checked without access. You can use the findings to plan further evaluation.

→ The buyer receives a clearer picture of moisture concerns and a practical basis for deciding whether additional inspection is needed.

04

A property owner wants to check a room after water-damage drying and before replacing drywall.

What we do: We review the affected area and drying history, scan the accessible surfaces, and verify selected spots with a moisture meter. Where the thermal pattern and readings agree, we identify the materials that merit attention. If they differ, we explain the discrepancy rather than treating the camera image as clearance.

→ You can make a better-informed decision about whether further drying or a separate verification step is appropriate before finishes go back in.

Thermal Imaging Across Colorado Springs

Colorado Springs buildings experience substantial daily and seasonal temperature changes, which affect how infrared images should be interpreted. In November and through winter, cold exterior surfaces can make temperature contrasts more noticeable, while heating cycles and closed windows can raise indoor humidity. We account for those conditions and compare suspect areas with similar surfaces rather than reading colors in isolation. Older homes in Old Colorado City and the Westside may have varied insulation, additions, or repaired finishes; newer and larger properties can have complex rooflines, multiple plumbing runs, and finished basements. Our Colorado Springs thermal imaging inspection combines surface scans with selected moisture readings to investigate water intrusion, condensation, and recurring stains. If you need to find a water leak with infrared imaging Colorado Springs, we start from the reported symptom and follow the likely path through accessible surfaces. We serve properties across El Paso County and explain when a plumber, roofer, or remediation contractor should take the next step. Thermal imaging is a diagnostic aid, not a substitute for code-required repair or mold testing.

Neighborhoods We Serve

  • Old Colorado City

    Older homes and later additions can have different wall assemblies and insulation levels. We compare like surfaces carefully so a construction change is not mistaken for a moisture pattern.

  • Broadmoor

    Larger homes may have multiple roof planes, finished lower levels, and extended plumbing routes. We focus the scan on the leak history and the rooms most likely to share a moisture path.

  • Downtown Colorado Springs

    Mixed building ages and renovated interiors can complicate comparisons between rooms. We record surface conditions and verify suspicious patterns with direct readings where access allows.

  • Briargate

    Finished basements and multi-level layouts can make water migration difficult to trace. We check the reported area and nearby surfaces rather than assuming the visible mark is the source.

Local Conditions We Plan For

  • Winter cold snaps create strong contrasts at exterior walls and windows

    Cold surfaces can help reveal temperature differences, but they also increase condensation risk and can imitate moisture anomalies. We consider indoor humidity, heating, and surface exposure before deciding which readings need verification.

  • Rapid weather shifts bring roof runoff and freeze-thaw exposure

    Roof edges, valleys, and penetrations can admit water that travels before staining appears. We ask about recent weather and repairs, then scan the ceiling and adjacent surfaces to help trace likely pathways.

  • Dry indoor air and localized humid rooms create uneven surface conditions

    Bathrooms, kitchens, and laundry areas can have higher humidity than adjoining rooms, while heating changes surface temperatures. We compare room conditions and use humidity measurements to distinguish condensation concerns from likely intrusion.

Recurring Ceiling Stain

Before

A homeowner had a ceiling stain that returned after a roof repair. The paint felt dry, but a musty odor remained near the hallway, and there was no clear way to tell whether the damp area stopped at the stain or extended into adjoining materials.

After

We scanned the ceiling and nearby wall, then checked four selected points with a moisture meter. Two locations showed readings that differed from the dry comparison area. The homeowner had a focused list of areas to review with the roofer and a clearer plan for monitoring after the next rain.

Maintenance: After roof work, check the ceiling after the next significant rain and note any new staining or odor. Keep repair photos and dates so a follow-up inspection can compare the same surfaces and readings.

Before

A repaired bathroom supply leak had wet the floor near a vanity. The visible water was gone, but the owner worried that moisture had moved behind the wall or beneath the adjacent flooring before the plumbing repair was completed.

After

We scanned the accessible wall and floor edges, then compared moisture readings at six locations. The strongest concern was limited to the area beside the vanity; readings farther along the wall were consistent with the comparison area. The owner could direct drying and repair work to a smaller, evidence-based zone.

Maintenance: Keep the vanity area accessible until drying and repairs are complete. Check supply connections periodically for drips, and address a recurring damp smell promptly rather than covering the area with new trim.

Before

After heavy weather, a basement room developed a musty smell near an exterior wall. There was no standing water, and the owner could not tell whether the odor came from condensation, a small intrusion, or an unrelated temperature difference.

After

We compared the exterior wall, an interior partition, and the floor perimeter with a thermal camera, then checked selected points with a moisture meter and hygrometer. Findings focused attention on one lower wall section for further evaluation, while the other scanned areas did not show the same pattern.

Maintenance: Keep stored items several inches from the wall, monitor indoor humidity, and note changes after wet weather. If staining or odor returns, arrange a follow-up before repainting or covering the surface.

Find Hidden Moisture Before Damage Spreads

Thermal imaging is most valuable when you have a specific concern but cannot see the full extent of it. We use the scan to prioritize physical checks, helping you decide whether a damp area needs repair, monitoring, or further investigation before finishes are replaced.

Problem

A ceiling stain returns after a roof leak appears repaired

Repeated staining can point to continuing water entry or moisture retained in nearby materials, increasing the chance of damaged drywall and concealed mold.

Our Fix

We scan the ceiling and adjoining surfaces, compare temperature patterns, and check selected locations with a moisture meter. You get a clearer map of areas to discuss with a roofer or restoration contractor, along with an explanation of whether the readings support additional drying or leak investigation.

Problem

A musty odor persists with no visible source

An odor can linger near hidden dampness, a concealed leak, or a poorly ventilated area, leaving you unsure where to investigate first.

Our Fix

We review the odor location and building history, then scan nearby walls, floors, and ceilings. Direct moisture checks help separate a suspicious thermal pattern from a dry temperature difference. If the evidence points to a concealed cavity, we explain whether targeted access or sampling would answer the next question.

Problem

A plumbing leak affected finished walls and flooring

Water may travel beyond the visible leak point, leaving damp materials under flooring or behind baseboards even after the plumbing is repaired.

Our Fix

We focus on the leak area and likely migration path, scan accessible surfaces, and compare readings across affected and unaffected materials. That evidence helps identify where drying or closer inspection is needed, so you can avoid replacing sound finishes while ensuring suspect areas are not overlooked.

Problem

Cold exterior walls show condensation and surface dampness

Recurring condensation can damage paint and trim and create conditions that support visible mold growth if moisture remains unmanaged.

Our Fix

We compare surface temperatures with room conditions and use a hygrometer to understand indoor humidity. The results help distinguish a moisture intrusion concern from condensation risk. We explain which locations need monitoring and whether ventilation, insulation review, or a separate building assessment is appropriate.

Clearer Answers, Less Guesswork

Clearer Answers, Less Guesswork

A useful scan narrows the search; it does not replace verification. We explain each finding in plain language and distinguish a temperature anomaly from a confirmed wet material. You get a practical record of areas to monitor, test, or repair.

  • Narrow The Search

    A thermal camera surveys broad wall and ceiling surfaces quickly, helping us focus follow-up checks where patterns differ from surrounding areas. In a typical room, we compare several adjacent surfaces rather than relying on one isolated reading. That makes it easier to investigate a suspected leak without opening multiple sections of finished wall.

  • Catch Hidden Dampness

    Water can migrate behind baseboards, under flooring, or across ceiling cavities before a stain becomes obvious. We use infrared patterns to guide moisture-meter checks and identify locations that deserve closer attention. This is especially useful after a pipe leak, roof entry, or appliance overflow that left an odor but no visible puddle.

  • Support Better Repairs

    A marked image and written location notes give your restoration or plumbing contractor a clearer starting point. We identify the affected surface and the verification readings, so a repair crew can target investigation rather than guessing across an entire wall. If sampling is warranted, we discuss the appropriate next step separately.

  • Document A Baseline

    A scan creates a useful snapshot of accessible areas on the inspection day. We record room locations, visible conditions, and selected moisture readings, then explain what changes to watch for over the next 24 to 48 hours after drying or repair. That record helps you compare later observations without treating images as a mold diagnosis.

Training And Standards

Licensed & Certified

  • IICRC Water Damage Restoration Technician — issued by Institute of Inspection, Cleaning and Restoration Certification
  • IICRC Applied Microbial Remediation Technician — issued by Institute of Inspection, Cleaning and Restoration Certification
  • ASTM D7338 Standard Guide for Assessment of Fungal Growth in Buildings — issued by ASTM International
  • ASTM D7391 Standard Test Method for Categorization and Quantification of Airborne Fungal Structures — issued by ASTM International

Verified Reviews

Customer feedback Not published

The inspection helped us narrow down a damp area after a pipe leak. We saw the thermal scan and the follow-up meter readings, and the technician explained why one cold spot was not enough to call it water damage. The room-by-room explanation gave us a practical next step.

Customer feedback Not published

We had a recurring stain in our Colorado Springs home and wanted someone to check beyond the paint. The technician scanned the ceiling and the nearby wall, then pointed out where the readings were different. The explanation was direct, and we knew what to ask our roofer to inspect.

Customer feedback Not published

Our basement smelled musty after wet weather, but there was no obvious leak. The inspection checked the exterior wall and compared it with other surfaces. We appreciated that the findings were described as clues to verify, not a claim that the camera had found mold.

Practical Inspection Expertise

Our team combines thermal patterns with building observations and direct moisture measurements instead of treating camera images as a final diagnosis. We work through common residential and commercial concerns, including roof or plumbing leaks, condensation and surface dampness, mold in attics, basements, and crawl spaces, and post-remediation mold concerns. Our inspection approach draws on relevant IICRC water-damage and microbial-remediation training, with attention to established assessment guidance such as ASTM D7338. We explain what the equipment shows, where its limits are, and what evidence would support the next decision.

  • We compare thermal anomalies with moisture-meter readings instead of calling a color difference proof of a leak.
  • Our field checks account for airflow, sunlight, insulation gaps, and temperature changes that can mimic wet materials.
  • We use Tramex and Protimeter moisture instruments where material readings help confirm or challenge an infrared pattern.
  • We apply IICRC Water Damage Restoration Technician principles when evaluating water-related conditions and drying concerns.
  • We separate evidence of dampness from evidence of mold, then recommend sampling only when it answers a specific question.
Get Started Today
Practical Inspection Expertise

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

Can thermal imaging detect moisture behind walls?
Thermal imaging can reveal surface-temperature patterns that point to possible moisture behind a wall, but it cannot confirm water by itself. We check suspicious areas with a moisture meter and compare readings with nearby dry material. Insulation gaps, airflow, sunlight, and plumbing temperature can produce similar patterns. If evidence remains unclear, we explain whether a borescope or targeted opening is the sensible next step.
How much does an infrared inspection cost in Colorado Springs?
A focused residential visit commonly costs about $250 to $650 and takes roughly 1.5 to 3 hours in 2026. Price changes with property size, the number of rooms, access, and whether additional moisture assessment is needed. We explain the price before work starts. A scan does not include mold sampling or destructive openings unless those services are separately arranged.
Does a thermal camera confirm mold is present?
No; a thermal camera cannot identify mold or confirm that mold is present. It shows surface-temperature differences that may help locate moisture conditions associated with mold risk. We inspect the area, check accessible materials, and explain whether sampling is appropriate. Mold identification requires suitable sampling and laboratory analysis, not an infrared image alone.
When is infrared moisture detection useful in Colorado Springs CO?
Infrared moisture detection is useful after a roof or plumbing leak, when staining returns, or when a musty odor persists despite visible cleanup. In Colorado Springs, winter temperature contrasts can also make cold surface patterns easier to notice, though we still verify with direct readings. Book an inspection when you need to find a water leak with infrared imaging Colorado Springs properties may be concealing behind finished surfaces.

Related Inspection Services

Mold Inspection

A visual mold inspection examines accessible surfaces, moisture sources, and building conditions. Thermal imaging can help target areas for closer attention, while the inspection determines whether visible growth or sampling deserves further evaluation in your Colorado Springs property.

View Mold Inspection

Residential Mold Inspection

For houses and condominiums, we connect infrared patterns with household leak history, odors, and material readings. A residential inspection can follow up on a bathroom ceiling anomaly, a damp basement wall, or an attic concern without assuming every temperature change means mold.

View Residential Mold Inspection

Commercial Mold Inspection

Commercial properties often have larger roof areas, mechanical rooms, and multiple tenant spaces. Infrared scanning helps prioritize follow-up checks across accessible surfaces, while a commercial inspection documents the conditions and rooms that need attention.

View Commercial Mold Inspection

Mold Testing and Sampling

When inspection findings leave a specific question about airborne or surface mold, sampling may add useful evidence. We first identify where a sample would be meaningful; infrared imaging can help locate a damp area, but it cannot replace laboratory analysis.

View Mold Testing and Sampling

Air Quality Testing for Mold

A persistent musty odor or concern about airborne particles may call for air sampling in addition to moisture investigation. We use inspection findings to select relevant locations and explain what air results can and cannot establish about conditions in your building.

View Air Quality Testing for Mold

Surface Mold Sampling

Surface sampling can help characterize visible suspect growth on an accessible material. Infrared findings may guide attention to nearby damp areas, but samples are collected from physical surfaces using suitable methods, not from a thermal image.

View Surface Mold Sampling

Book Thermal Imaging in Colorado Springs

A recurring stain or unexplained musty odor deserves a targeted check before repairs cover the evidence. Our team combines thermal patterns with direct moisture readings and explains the next step clearly. Call Colorado Springs Mold Testing to schedule your inspection.

Call Today Schedule Inspection

Contact Our Inspection Team

Call Colorado Springs Mold Testing at +1 866-896-8166 to talk through a leak, musty odor, visible growth, or post-remediation question. Our office hours are Monday through Friday, 8:00 a.m. to 6:00 p.m.; leave a message outside those hours and we will respond during the next business period. We serve Colorado Springs, CO, including ZIP codes 80909, 80904, and 80906.

Or call us right now at +18668968166 — we answer.

Colorado Springs Mold Testing


  • Phone

    +18668968166
  • Address

    Colorado Springs

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote